Motorbike & Motorcycle Battery Charger Scooter & moped Battery Charger Vintage Motorcycle 6 Volt Battery Charger Snowmobile Battery Charger Watercraft Battery Charger ATV & Four Wheeler Battery Charger Car Battery Charger Vintage Car Battery Charger Caravan and RV Battery Charger Gardening and Lawnmower Battery Charger Motor Boat Battery Charger Sailing Boat Battery Charger

Battery Charger Installation

Battery Connector with Eyelets - STD2V - Installation Procedure

The following operations are necessary for a correct set-up of the device. Please note the recommended cables configuration (STD2V cable always on-board and connected to the battery poles) allows you to perform this procedure just once.
The user is kindly requested to execute the installation with maximum care (see Directions and Safety section on the manual). If necessary, please entrust qualified personnel with the execution of the steps reported here below:

  1. Connect the cable STD2V to the battery: connect the black wire to the (-) negative Battery pole, the red wire to the (+) positive battery pole.

Moreover, in order to ensure a regular functioning, it is suggested to periodically check the correct and stable connection of the eyelets to the Battery and the removal of eventual dust and oil from poles with a metallic brush.

-----------------------------------------------------------------------------

Battery Charger Installation Procedure

  1. Connect the device (off state) to the power outlet.
  2. Verify that the battery charger is on (LCD display or red LED on, signaling that the battery is not connected).
  3. Remove the connector saver cap from the STD2V battery cable and connect the battery charger to the battery cable. Alternatively, connect the battery charger to the cigar socket through ACC612V (Universal Cigar Socket Adapter) or directly to the battery poles through 30AMPPZ (Battery Connector with Clamps).

Once connected, the battery charger will start the charging cycle.

-----------------------------------------------------------------------------

Battery Charger Disconnection Procedure

  1. Disconnect the device from the power outlet.
  2. Disconnect the device from the battery cable with eyelets (or clamps, or cigar socket adapter).
  3. Restore the connector saver cap on the STD2V battery cable connector.
  4. Put the battery cable cable back in its hiding place.
  5. Put the battery charger back in its box to minimise its exposure to the atmospheric agents.
BC BATTERY CHARGERS
FOR HOME BATTERY CARE
BC DUETTO - TWO CHARGING PROGRAMS
FOR LEAD-ACID BATTERIES (WET, GEL,
MF, AGM...) AND LITHIUM BATTERIES
Lead-Acid/Lithium Battery Charger BC DUETTO
BC BATTERY CHARGERS
FOR LEAD-ACID BATTERIES
(WET, GEL, MF, AGM, VRLA...)
BC K900 6/12V BC BRAVO 1500
+ 12V CAN-Bus CHARGE & TEST
BC K900 6/12V battery charger and maintainer BC BRAVO battery charger and tester
BC SMART 1500 BC JUNIOR 1500
BC SMART battery charger and maintainer BC JUNIOR battery charger and maintainer
BC EASY 6 BC EASY 4
BC EASY 6 battery charger and maintainer BC EASY 4 battery charger and maintainer
PROFESSIONAL BATTERY CARE
BC Pro 4S BT02
BC Pro 4S - Professional battery charger with 4 units BT02 battery and alternator tester
PRIVATE USERS
Select the right battery charger
- for your motorcycle >>
- for your car >>
- for your battery >>
 
Where to buy >>
Information Request >>
F.A.Q. - Frequently Asked Questions >>
PROFESSIONAL USERS
Join BC Distribution Network >>
Find BC Distributors in your Country >>
BC Pro Series - Professional
Battery Chargers & Testers
- BC Pro 4S - Professional Charger for Lead-Acid and Lithium Batteries >>
- BT02 6/12V Battery Test 40-2000 CCA
  + 12/24V Charging System Test >>

- Accessories >>
FAIRS AND EXIBITIONS
EICMA 2018 - 06-11 November - Milan - Hall 13 Stand S-66
INTERMOT 2018 - 03-07 October - Cologne - Hall 9 Stand E-023
Automechanika Frankfurt 2018 - September 11-15 - Frankfurt
Automechanika Dubai 2018 - May 01-03 - Dubai
Expomecanica 2018 - April 20-22 - Porto
Motor Bike Expo 2018 - January 18-21 - Verona
Motorcycle Trade Expo 2018 - January 14-16 - Stoneleigh Park
Automechanika Birmingham 2017 - June 6-8 - NEC Birmingham
Autopromotec 2017 - May 24-28 - Bologna
Ticino Motor Expo 2017 - April 08-09 - Lugano
PRESS
Company Profile
Home  |  Company  |  Contact Us  |  Site Map